 |
Moderated by: . |
Page: 1 2 |
|
Posted: Wed Jul 20th, 2022 10:58 am |
|
1st Post |
Tim H
Registered
Joined: | Sun Dec 14th, 2014 |
Location: | United Kingdom |
Posts: | 193 |
Status: |
Offline
|
|
This may not be the right place to post this query,
but here goes.
Just started a Peco wooden laser-cut kit for a diorama,
it is lovely but fiddly, however my main concern,
is how to finish the building ?
All the detail is printed on,
there is no raised surface detail,
and a layer of paint would obliterate the details.

My first thought
would be to apply a wash of very dilute acrylic,
opaque enough to colour the wood,
but not to lose the surface printed detail.
Laser-cut kits are not as prolific across the pond,
and any suggestions would be welcome.
Thank you.
Tim
____________________ Tim H
http://timhalesblog.blogspot.co.uk
|
|
Posted: Wed Jul 20th, 2022 11:02 am |
|
2nd Post |
Rod Hutchinson
Registered

|
What raised detail do you mean ?
____________________ Rod Hutchinson
Mooroolbark, Australia
|
|
Posted: Thu Jul 21st, 2022 05:03 am |
|
3rd Post |
Posted: Thu Jul 21st, 2022 09:18 am |
|
4th Post |
Tim H
Registered
Joined: | Sun Dec 14th, 2014 |
Location: | United Kingdom |
Posts: | 193 |
Status: |
Offline
|
|
A few minutes ago,
a new set of eaves for the pitched roof were made,
the images shows their supports being glued into place.
Unfortunately, there seems to be a shortage of 1mm ply,
I will be using card, it has the advantage
of being available and compatible with ply.
I intend to apply a very dilute wash of acrylic light grey,
enough to colour the wood but not to obscure the printed lines.
Below is someone's previous attempt,
it has not been stained.

____________________ Tim H
http://timhalesblog.blogspot.co.uk
|
|
Posted: Thu Jul 21st, 2022 03:11 pm |
|
5th Post |
Posted: Thu Jul 21st, 2022 07:02 pm |
|
6th Post |
Tim H
Registered
Joined: | Sun Dec 14th, 2014 |
Location: | United Kingdom |
Posts: | 193 |
Status: |
Offline
|
|
Everyday the little wooden building progresses,
the glued joints of the modified roof will harden overnight,
otherwise it is OK.
I intend to experiment on some scrap bits
with acrylic light grey thinned with water+alcohol,
not a thick layer, just a wash.
The plastic windows and doors are just waiting to be glazed,
always a faff.
The building is quite small, enough for a low key diorama.
Follow the build in this link
Tim
____________________ Tim H
http://timhalesblog.blogspot.co.uk
|
|
Posted: Thu Jul 21st, 2022 10:35 pm |
|
7th Post |
Reg H
Moderator

Joined: | Sun Oct 19th, 2014 |
Location: | Shelton, USA |
Posts: | 1109 |
Status: |
Offline
|
|
Nice looking build.
I have never encountered printed details
(except in some card buildings)
It seems a bit strange.
Looking forward to photos of the diorama.
Reg
____________________ Reg
|
|
Posted: Fri Jul 22nd, 2022 12:22 am |
|
8th Post |
Posted: Sat Jul 23rd, 2022 09:52 am |
|
9th Post |
Tim H
Registered
Joined: | Sun Dec 14th, 2014 |
Location: | United Kingdom |
Posts: | 193 |
Status: |
Offline
|
|
A bit more progress.

A wash with very dilute Amish Grey acrylic by DecorArt
has not obscured the printed lines, the intended effect
is a weather-worn clapboard structure near the sea.
Once completely dry, tomorrow, a wash with
MiG green mould and some highlights with charcoal.
The corrugated roof needs to be rusty and weathered,
usually the iron would have been tarred
but over the years this wears to a light grey.
It isn't worth detailing the interior
but a chair on the stoop would not go unnoticed.
____________________ Tim H
http://timhalesblog.blogspot.co.uk
|
|
Posted: Sat Jul 23rd, 2022 11:34 am |
|
10th Post |
Nice Guy Eddie
Administrator

Joined: | Mon Sep 5th, 2016 |
Location: | Long Beach CA |
Posts: | 408 |
Status: |
Offline
|
|
The detailing produced by the burnt in lines,
normally produces a slight depression in the wood,
where the material has been vaporized away.
The kit designers apply it like injection moulding,
it can usually be painted over totally opaque,
and dealt with a bit like scribed basswood siding.

Eddie
____________________ " We Got Places All Over The Place "
|
|
 Current time is 10:55 pm | Page: 1 2 |
|
 |
|