 |
Tim H
Registered
| Joined: | 14 Dec 2014 |
| Location: | United Kingdom |
| Posts: | 199 |
| Status: |
Offline
|
|
This may not be the right place to post this query,
but here goes.
Just started a Peco wooden laser-cut kit for a diorama,
it is lovely but fiddly, however my main concern,
is how to finish the building ?
All the detail is printed on,
there is no raised surface detail,
and a layer of paint would obliterate the details.
My first thought
would be to apply a wash of very dilute acrylic,
opaque enough to colour the wood,
but not to lose the surface printed detail.
Laser-cut kits are not as prolific across the pond,
and any suggestions would be welcome.
Thank you.
Tim
____________________
Tim H
https://antiochny.blogspot.com/
|
|
|
Rod Hutchinson
Registered
|
What raised detail do you mean ?
____________________
Rod Hutchinson
Mooroolbark, Australia
|
|
|
Tim H
Registered
| Joined: | 14 Dec 2014 |
| Location: | United Kingdom |
| Posts: | 199 |
| Status: |
Offline
|
|
A few minutes ago,
a new set of eaves for the pitched roof were made,
the images shows their supports being glued into place.
Unfortunately, there seems to be a shortage of 1mm ply,
I will be using card, it has the advantage
of being available and compatible with ply.
I intend to apply a very dilute wash of acrylic light grey,
enough to colour the wood but not to obscure the printed lines.
Below is someone's previous attempt,
it has not been stained.
____________________
Tim H
https://antiochny.blogspot.com/
|
|
|
Tim H
Registered
| Joined: | 14 Dec 2014 |
| Location: | United Kingdom |
| Posts: | 199 |
| Status: |
Offline
|
|
Everyday the little wooden building progresses,
the glued joints of the modified roof will harden overnight,
otherwise it is OK.
I intend to experiment on some scrap bits
with acrylic light grey thinned with water+alcohol,
not a thick layer, just a wash.
The plastic windows and doors are just waiting to be glazed,
always a faff.
The building is quite small, enough for a low key diorama.
Follow the build in this link
Tim
____________________
Tim H
https://antiochny.blogspot.com/
|
|
|
Reg H
Moderator
| Joined: | 19 Oct 2014 |
| Location: | Shelton, USA |
| Posts: | 1241 |
| Status: |
Offline
|
|
Nice looking build.
I have never encountered printed details
(except in some card buildings)
It seems a bit strange.
Looking forward to photos of the diorama.
Reg
____________________
Reg
|
|
|
Tim H
Registered
| Joined: | 14 Dec 2014 |
| Location: | United Kingdom |
| Posts: | 199 |
| Status: |
Offline
|
|
A bit more progress.
A wash with very dilute Amish Grey acrylic by DecorArt
has not obscured the printed lines, the intended effect
is a weather-worn clapboard structure near the sea.
Once completely dry, tomorrow, a wash with
MiG green mould and some highlights with charcoal.
The corrugated roof needs to be rusty and weathered,
usually the iron would have been tarred
but over the years this wears to a light grey.
It isn't worth detailing the interior
but a chair on the stoop would not go unnoticed.
____________________
Tim H
https://antiochny.blogspot.com/
|
|
|
Nice Guy Eddie
Registered
| Joined: | 5 Sep 2016 |
| Location: | Long Beach CA |
| Posts: | 411 |
| Status: |
Offline
|
|
The detailing produced by the burnt in lines,
normally produces a slight depression in the wood,
where the material has been vaporized away.
The kit designers apply it like injection moulding,
it can usually be painted over totally opaque,
and dealt with a bit like scribed basswood siding.
Eddie
____________________
" We Got Places All Over The Place "
|
|
|
Tim H
Registered
| Joined: | 14 Dec 2014 |
| Location: | United Kingdom |
| Posts: | 199 |
| Status: |
Offline
|
|
Yesterday evening the roof was painted with artist's burnt sienna,
when dry it was much too 'bold' and needed letting down.
This is just after a wash of DecorArt Amish Grey
that is well-diluted but still wet,
it will change colour when fully dry.
Still lots to do,
a chair for the stoop and weathering for the clapboard.
Tim
____________________
Tim H
https://antiochny.blogspot.com/
|
|
|
Rod Hutchinson
Registered
|
I would try drybrushing colours.
Less impact on raised detail,
and makes for a weathered appearance.
____________________
Rod Hutchinson
Mooroolbark, Australia
|
|
|
Tim H
Registered
| Joined: | 14 Dec 2014 |
| Location: | United Kingdom |
| Posts: | 199 |
| Status: |
Offline
|
|
The trick with weathering is knowing when to stop.
The 'office' merely needed a wash to let-down the roof colour (now dry)
and a subtle touch of muck on the front step
and at the corners of the window where the water drips off the sill.
I am going to leave it alone for a few weeks
and see how it works with the other structures.
That's all folks, you can follow the
building of the diorama on this blog
Tim
____________________
Tim H
https://antiochny.blogspot.com/
|
|
|
Current time is 07:35 pm | |
|
|
|
